Pilot-RC 75in Wingspan Sbach 342 V2

  Click On Images to Enlarge

Overview

Introducing the NEW Pilot RC Sbach 342 V2 75in

The next-generation Sbach 342 is here, This V2 design masterfully combines the legendary smoothness of the original 73in Sbach with unmatched, modern Xtreme Aerobatics (XA) precision.

Constructed with a full airframe of new plywood, composite fibreglass, and carbon fibre—consistent with our current 3D aircraft—it is built for performance. After extensive testing and design refinements, we have perfected its flight characteristics.

Specifications:

Model:	Sbach 342 V2
Wingspan:	75in (1.90m)
Length:	74in (1.87m) including spinner 3.5inch
Wing area:	1,125sq in (7,264sq cm)
Weight:	12.3lbs (5.6kg)

Features:

• NEW! Hybrid construction from wood and composite materials for specially reinforced fuselage and wings.
• NEW! Patented quick assembly system for wings, stabiliser and SFG
• NEW! Patented quick assembly system for canopy.
• Film covering applied over a Genuine German Oracover (Ultracote) base
• Highly prefabricated, experienced builders can have air ready in under a day
• Pre-installed hinges (glued and pinned)
• Internally mounted cowling – so no visible external screws exposed (two exposed screws underneath for easy mounting)
• Removable wings and NEW quick release for stabs no tools require
• Laser engraved motor mounting position
• Easy canister installation due to open construction
• Pull push and Pull pull system for Rudder servo

Included Hardware:

• Complete air frame with all basic accessories (such as carbon fiber main undercarriage, tail-gear assembly and wing-tubes as well as fiberglass control horns and wheel pants)
• "Spare" lower section cowl from transparent plastic – used to mark out correct location to cut the cowl for perfect fitting every time
• Pre-installed hinges and pre-mounted canopy
• Fuel tank and fuel tubing pre-prepared, fuel dot and breather valve
• Wheels, axles and wheel pants
• Pre-prepared pushrods with ball links
• Matching 3.5in carbon spinner

"Spare" transparent cowl for easy markings

Crash Kits Available For This Model:

• Landing gear repair package. Includes the wooden parts required to repair the damage often suffered around the landing gear area.
• Front fuselage repair package. Includes the wooden parts required to repair the damage often suffered around the front of the model.
• Please note that additional or alternative spare wood outside of the above Packs is not available to order.

Images for illustration purposes only – exact contents vary per package, model and size.

Required Hardware:

Motor: 30-40cc or equivalent electric

Servos: 5 high torque plus throttle // Uses x1 per aileron, x1 per elevator half and x1 on rudder

Also requires all the usual accessories such as transmitter, receiver, propeller, batteries, powerbox, extension leads and possibly other small accessories.

Recommended Hardware:

Servos: Pilot-RC PW-28AH 28.7kg.cm/0.056s High Torque Brushless Servo or MacGregor MGB6928HV2 28Kg/0.05s HV Brushless Digital Servo

Elevator Servo: Pilot-RC PW-21AH 21.5kg.cm/0.079s High Torque Brushless Servo or MacGregor MGB5216HV 16.0kg/0.08s Brushless High Voltage Servo

Servo arms: Pilot-RC 1.6in Aluminium arms (included with Pilot-RC servos) - PIL302

Wingbags: Pilot-RC 35cc Wingbags V2 - PIL882

Video:

Pilot-RC Sbach 342 V2 75in flown by Ryu

Build information

Cowl Size:

A: -mm | B: -mm | C: -mm | D: -mm

Exhaust Tunnel Size

A: -mm | B: -m | C: -mm | D: -mm | E: -mm | F: -mm

Rudder Horns and Pull Pull Location

A: N/A | B: N/A | C: N/A | D: 5mm | E: 8.5mm

Extension Wire Lengths:

Each aileron: 15cm (to reach receiver direct)

Each elevator: 65cm

Rudder: pull pull no extenstion required

Centre Of Gravity:

148mm - Measured back from leading edge of the wing at the fuselage.

You will find a laser engraved C.G. emblem on the inside of the fuselage, located close to the wing tube, which also shows the exact location for Centre of Gravity.

Manuals/Downloads

• Pilot-RC 35cc Online Build Manual (Pilot-RC Website)